DEATH GRIP TIE ROD INSTALLATION INSTRUCTIONS

Installation instructions for the Kryptonite Tie Rod Kit (KRTR10, KRTR11, KRTR12). Used with: Kryptonite Tie Rod Kit for 2001–2010 Chevy/GMC 1500HD/2500HD/3500HD, 2001-2013 Chevy Suburban/GMC Yukon XL 2500 & 2002–2009 Hummer H2, Kryptonite Tie Rods for 1999-2006 GM 1500 Trucks & SUVs, Kryptonite Tie Rods (Fabtech Rts Lift Kits) for 2011+ Chevy/GMC 2500HD/3500HD, Kryptonite Tie Rods for SS Series Center Link for 2001–2010 Chevy/GMC 1500HD/2500HD/3500HD, 2001-2013 Chevy Suburban/GMC Yukon Xl 2500 & 2002–2009 Hummer H2 and 2 more.

Quick reference

  • Part numbers: KRTR10, KRTR11, KRTR12
  • Inner joint-centerlink connection, 99-10 trucks (red Loctite, 2" crow's foot): 74 ft-lbs
  • Inner joint-centerlink connection, 11-19 trucks (red Loctite, 2" crow's foot): 92 ft-lbs
  • Inner joint-centerlink connection, 20+ trucks (red Loctite, 2" crow's foot): 118 ft-lbs
  • End nut (outer to spindle), 99-10 trucks: 37 ft-lbs
  • End nut (outer to spindle), 11+ trucks: 26 ft-lbs then 85-100°
  • Jam nuts (confirm again after alignment): 200 ft-lbs
  • Rod ends grease: 6-8 pumps of grease after installation

Text version of these instructions

Removal

  1. Park on a level surface and chock rear tires. Raise the front of the truck and support with jack stands under the frame. Remove front wheels.
  2. Be sure to note what side of the spindle the tie rods on the truck are oriented - they will either be mounted from the top or the bottom. The Kryptonite Tie Rod will be installed in the same orientation.
  3. Start on the driver's side of the truck. Remove the nut securing the tie rod to the spindle. Using a large hammer, strike the outer joint upwards to free it from the spindle.
  4. Using a large crescent wrench, remove the inner tie rod from the centerlink, then remove the tie rod as one piece so you can measure the length.
  5. Repeat steps 2 & 3 for the passenger side.
  6. With the tie rod removed, measure the overall length of the tie rod and write it down.
  • Record: Driver side ____ / Passenger side ____

Installation

  1. With the measurements recorded, begin setting up the Kryptonite Tie Rods. Apply anti-seize to the threaded shank of the tie rod inner and outer joints.
  2. Thread the ends back into the tie rod body. Be sure you have an even amount of exposed threads on both ends of the tie rod body. This ensures full adjustability while maintaining safe thread engagement.
  3. Prior to installation onto the centerlink: Clean the area and remove any excess grease from the threads in the centerlink. This connection will require red Loctite. Torque the inner joint-centerlink connection. For 99-10 trucks 74 ft-lbs, 11-19 trucks 92 ft-lbs, 20+ trucks 118 ft-lbs. Do this using a 2" crow's foot.
  4. Connect the outer to the spindle. If the stud rotates before you seat the taper, use the wrench flats on the end of the stud while using a box wrench to run the nut down. Torque the end nut. For 99-10 trucks, 37 ft-lbs. For 11+ trucks 26 ft-lbs then 85-100°.
  5. Torque the jam nuts down to 200 ft-lbs.
  6. Repeat steps 3 & 4 on the opposite side of the vehicle.
  7. With the truck still lifted off the ground, cycle the steering making sure there is adequate clearance. Be sure to get an alignment as soon as possible in order to avoid premature tire wear.
  8. Grease the rod ends with 6-8 pumps of grease after installation.
  • Due to the larger diameter of the Kryptonite tie rods, longer sway bar end links may be required on some applications. It is required to take your truck to get to a professional alignment to properly set your toe after installation. Confirm jam nuts are torqued to 200 ft-lbs. after alignment.

Warnings

  • It is required to take your truck to get to a professional alignment to properly set your toe after installation.

Important safety and legal information

Installation should be performed by a qualified technician. Improper installation may result in vehicle damage, loss of control, serious injury, or death. Always support the vehicle securely with jack stands. Never rely on a jack alone. Verify all components are installed correctly and torqued to specification before operating the vehicle. After installation, inspect suspension and steering components and check for proper clearance through full travel. Re-torque all hardware after initial use and periodically thereafter. User assumes all responsibility for compliance with local laws. Manufacturer is not responsible for damage or injury resulting from improper installation, misuse, or modification. By installing this product, the user accepts all risk and liability associated with its use.