SS Series Center Link Pack Installation Instructions
Installation instructions for the Kryptonite CENTERLINK & TIE ROD KIT (KRCLP88, KRCLP99, KRCLP10, KRCLP11). Used with: Kryptonite SS Centerlink and Tie Rod Package 2001–2010 GM HD Trucks & 2002-2009 Hummer H2, Kryptonite SS Center Link and Tie Rod Package for 2011–2026 Chevy/GMC 2500HD/3500HD, Kryptonite SS Series Center Link Upgrade Kit for 2001–2010 Chevy/GMC 1500HD/2500HD/3500HD & 2002–2009 Hummer H2, Kryptonite SS Series Centerlink Tie Rod Package K-Series 1988-1999 and 6 more.
Quick reference
- Part numbers: KRCLP88, KRCLP99, KRCLP10, KRCLP11
- Idler and pitman arm to the centerlink (88-98 trucks): 40 ft-lbs
- Idler and pitman arm to the centerlink (99-10 trucks): 46 ft-lbs
- Idler and pitman arm to the centerlink (11+ trucks): 92 ft-lbs
- Idler support (88-98 trucks): 78 ft-lbs
- Idler support (99-06 1500 trucks): 110 ft-lbs
- Idler support (01-10 HD trucks): 73 ft-lbs
- Idler support (11+ trucks): 92 ft-lbs
- Steering box bolts (88-98 trucks): 69 ft-lbs
- Steering box bolts (99-10 trucks): 110 ft-lbs
- Steering box bolts (11+ trucks): 203 ft-lbs
- Inner tie rod ends into the centerlink (99-10 trucks): 37 ft-lbs
- Inner tie rod ends into the centerlink (11+ trucks): 26 ft-lbs then 85-100°
- Outer tie rod ends into the steering knuckles (99-10 trucks): 37 ft-lbs
- Outer tie rod ends into the steering knuckles (11+ trucks): 26 ft-lbs then 85-100°
- Jam nuts (after setting toe): 200 ft-lbs
- Jam nuts on the tie rod bodies (retorque after alignment): 200 ft-lbs
Text version of these instructions
Removal
- Remove the front skid plate & splash guard (if equipped) and set aside.
- Disconnect your outer tie rods from the steering knuckles. Remove the retaining nut and strike the steering knuckle with a hammer to release the taper.
- Remove the steering stabilizer (if equipped).
- Disconnect the centerlink from the pitman arm and idler arm. Remove both retaining nuts and use a puller to separate the tapers.
- Remove the complete centerlink and tie rod assembly from the vehicle.
Installation
- Slightly loosen the idler arm support & steering box mounting bolts. This allows movement for proper centerlink alignment.
- Install the Kryptonite centerlink onto the pitman arm & idler arm studs. Ensure the Kryptonite logo is facing forward and the side containing the additional hole for the steering stabilizer is toward the passenger side.
- Torque the idler and pitman arm to the centerlink to spec: For 88-98 trucks, 40 ft-lbs. For 99-10 trucks, 46 ft-lbs. For 11+ trucks 92 ft-lbs.
- Cycle the steering lock-to-lock to level the centerlink, it should be parallel with the front crossmember. Tighten the idler support to spec: For 88-98 trucks, 78 ft-lbs. For 99-06 1500 trucks, 110 ft-lbs. For 01-10 HD trucks, 73 ft-lbs. For 11+ trucks 92 ft-lbs.
- Torque the steering box bolts to spec: For 88-98 trucks, 69 ft-lbs. For 99-10 trucks, 110 ft-lbs. For 11+ trucks 203 ft-lbs.
- Apply anti-seize to all tie rod threads and assemble both tie rod assemblies. Be sure they are threaded in evenly.
- Install the inner tie rod ends into the centerlink. The tie rod end & jam nut with the left hand thread identification marks install at the spindle side of the assembly. The inner tie rod stud should be facing the front of the truck. Torque to spec: For 99-10 trucks, 37 ft-lbs. For 11+ trucks 26 ft-lbs then 85-100°.
- Install the outer tie rod ends into the steering knuckles. Use the same taper orientation as removed during disassembly. Torque to spec: For 99-10 trucks, 37 ft-lbs. For 11+ trucks 26 ft-lbs then 85-100°.
- Set your toe as close as you can and torque the jam nuts down to 200 ft-lbs.
- Grease each tie rod end. Cycle the steering lock-to-lock and verify adequate clearance throughout suspension travel.
- NOTE: Due to the larger diameter of the Kryptonite tie rods, longer sway bar end links may be required on some applications. It is required to take your truck to get to a professional alignment to properly set your toe after installation. Be sure to retorque the jam nuts on the tie rod bodies to 200 ft-lbs after alignment.
Warnings
- IMPORTANT: Note the orientation of the factory tie rods before removal. The Kryptonite tie rods must be installed in the same orientation (top or bottom mounted).
Important safety and legal information
Installation should be performed by a qualified technician. Improper installation may result in vehicle damage, loss of control, serious injury, or death. Always support the vehicle securely with jack stands. Never rely on a jack alone. Verify all components are installed correctly and torqued to specification before operating the vehicle. After installation, inspect suspension and steering components and check for proper clearance through full travel. Re-torque all hardware after initial use and periodically thereafter. User assumes all responsibility for compliance with local laws. Manufacturer is not responsible for damage or injury resulting from improper installation, misuse, or modification. By installing this product, the user accepts all risk and liability associated with its use.