2007-2018 1500 Upper Control Arm Installation Instructions

Installation instructions for the Kryptonite 2007-2018 GM 1500 UPPER CONTROL ARMS (KRUCA12, KRUCA13). Used with: Kryptonite Upper Control Arm Kit for 1/2 Ton 6-LUG Chevy/GMC Trucks 2007–2018, Kryptonite Stage 3 Leveling Kit with Fox Shocks for 2007–2018 1/2 Ton 6-LUG Chevy/GMC Trucks, Kryptonite Stage 3 Leveling Kit with Fox Shocks for 2014–2018 1/2 Ton 6-LUG Chevy/GMC Trucks, Kryptonite Stage 2 Leveling Kit for 2007–2018 1/2 Ton 6-LUG Chevy/GMC Trucks and 1 more.

Quick reference

  • Part numbers: KRUCA12, KRUCA13
  • Ball joint mounting hardware: 22 ft-lbs
  • Control arm bolts (old style cam plates): 90 ft-lbs
  • Control arm bolts (new style cam plates): 140 ft-lbs
  • Ball joint castle nut: 37 ft-lbs, then 90-100 degrees
  • Upper ball joint grease (zerk fitting): typically 4-6 pumps
  • Bushing grease (each zerk fitting): typically 3-4 pumps
  • Wheels: 140 ft-lbs

Text version of these instructions

Removal

  1. Put the truck into park, engage the parking brake, and chock rear tires. Jack the front of the truck off the ground and support the frame with jack stands.
  2. Support the lower control arm with a floor jack, raising the suspension slightly from full droop. This relieves pressure on the upper ball joint.
  3. Remove the cotter pin (if equipped) and loosen the upper ball joint nut. Leave the nut threaded a few turns to prevent uncontrolled separation.
  4. Support the knuckle to avoid putting strain on the CV axle, brake lines, and ABS sensor wiring when the control arm is disconnected.
  5. Break the taper by using a pickle fork or by striking the knuckle boss with a hammer. Separate the upper control arm from the spindle once the taper is broken and the stud is free.
  6. Remove the factory bolts and cam plates from the frame pockets. Clean up and keep the cam bolt hardware set aside.

Assembly

  1. Install the polyurethane bushings into the upper control arms. Do not grease the outside of the bushings or the control arms. Press in the metal sleeves, use a rubber mallet if needed. Install the 90° zerk fittings.
  2. Ball joint placement depends on the UCA position. Mount on top of the UCA if it sits flat/near OEM angles; mount on the bottom if it droops or angles downward. You want the ball joint pocket to be as flat as possible. Torque mounting hardware to 22 ft-lbs.

Installation

  1. Identify left vs. right. Each arm has an arrow near the ball joint. The arrow & logo plate must point forward when installed. Install the arm into the frame pockets. Install the control arm bolts and cam plates. Torque to spec (For old style torque to 90 ft-lbs, For new style torque to 140 ft-lbs)
  2. Attach the ball joint to the knuckle by swinging the control arm down until the ball joint stud lines up with the knuckle bore. Insert the stud and install the supplied castle nut. If the cotter-pin hole does not align, do not loosen the nut, use the provided 9/16" flat washers to space the castle nut. Torque to 37 ft-lbs, then 90-100 degrees.
  3. Grease the upper ball joints. Add grease to the zerk fitting (typically 4-6 pumps). Over-greasing until the boots swell will rupture the boot.
  4. Grease the bushings. Add grease to each zerk fitting (typically 3-4 pumps).
  5. Reinstall the wheels and torque to 140 ft-lbs.
  6. Be sure to get a professional alignment immediately to avoid uneven tire wear.
  • NOTE: You may need to use a 9/16" drill bit to chase the narrow side of the spindle opening in order to allow the threaded portion of the ball joint stud to drop through.

Warnings

  • Do not grease the outside of the bushings or the control arms.
  • Over-greasing until the boots swell will rupture the boot.
  • If the cotter-pin hole does not align, do not loosen the nut, use the provided 9/16" flat washers to space the castle nut.

Important safety information

Installation should be performed by a qualified technician. Improper installation may result in vehicle damage, loss of control, serious injury, or death. Always support the vehicle securely with properly rated equipment. Never rely on a jack alone. Follow all installation procedures and torque specifications. Before operation, verify all components are properly installed and free from interference through the full range of steering and suspension travel. Inspect and re-torque all hardware after initial use and periodically thereafter. Aftermarket components may alter vehicle handling, steering, suspension geometry, braking, or other vehicle dynamics. Drive cautiously and become familiar with any changes before normal operation. Do not exceed manufacturer vehicle limits. The owner and installer are responsible for safe operation and compliance with applicable laws.